ElecGear Hall Joystick Kit Replacement for Universal Controllers, 2x Hall Effect Control Stick + 2x Calibration PCB + Desoldering Repair Tools for Analog Stick Thumbsticks – HL-UniA

Price: £25.16
(as of Jul 08, 2024 14:08:24 UTC – Details)

Model: HL-UniA
🔺This UniA version of Repair kit was rated 10 difficulty. Not for beginners
Hall Joysticks Replacement for Most Normal ALPS, FU and 3rd Joysticks
Calibration PCB with MCU for the finest Centering and Rocking Curve
Stack on the back of the PCB, or Link the individual Wires off the PCB
A Copper Heating Plate and Solder Wick help a lot for the Desoldering

ATTENTIONs before Ordering:
1.🔺Thoroughly read the page and images, measure the joystick and PCB before ordering
2.🔺This UniA fits normal analog sticks measured 19.0 mm on the image. While UniB is for 20.2 mm sticks
3.🔺Serious electronic know-how and soldering skills required. Not for newbies
4.🔺Turn to ours HL-PS4, PS5, DSE, Xbox and NSPro for these specific controllers
5.🔺Make sure your controller works with the tester web link (View the image), and see if your controller shows the LR circles. (Other joystick test tool is also OK.)
6.🔺Teardown screwdriver tools, USB wired/wireless controllers, other soldering tools and materials are required, however NOT included

ATTENTIONs before Operation:
1.🔺Fully read the installation guide. And understand the DEMOs before DIY
2.🔺Before desolder the old analog stick off, the main board should be carefully measured with a multi-meter

Reminder on the Button and Calibration:
1.The button signal will be used when calibrating. The button in the stick will work in 99% cases. In case it does not work, remove the connection on C1 and C2, use the onboard button instead
2.Study if your controller has a built-in App or power-on self-calibration. Co-work these settings with the calibration modes

What’s in the box:
2x Hall Joysticks UniA
2x Calibration PCB UniA
1x Heating Plate
1x Solder Wick
5x Color Wires for wiring off the PCB
1x Installation Guide in English alone

Package Dimensions ‏ : ‎ 7 x 6.9 x 1.9 cm; 40 g
Date First Available ‏ : ‎ 8 July 2024
Manufacturer ‏ : ‎ ElecGear
ASIN ‏ : ‎ B0CYBZ8F8Y
Item model number ‏ : ‎ HL-UniA
Guaranteed software updates until ‏ : ‎ unknown

[2x Hall Joysticks for Universal Controller] – This UniA kit is to replace the normal analog stick with hall joystick for wireless and wired USB controllers. The hall sensor delivers higher sensitivity and accuracy. No more wear of traditional carbon film resistor, say goodbye to drifting. (🔺Before ordering, make sure you follow the steps presented on the 2nd image. 🔺This UniA fits normal analog sticks measured 19.0 mm on the image. While UniB is for 20.2 mm sticks.)
[2x Added-on Calibration PCB] – Two options to install the PCB. Stack on the back of main board, or house it at a free position and link individual wires remotely if there’s some interference in the structure. The hall signal inputs to the MCU, the calibrated signal outputs to the main board. Connect the controller to a PC with a USB cable. You can fine reset the center and trim the curve on a web link
[Attention] – 1.🔺It takes serious electronic know-how and soldering skills. Not for newbies. 2.🔺Carefully follow the steps on the image before ordering. 3.🔺Make sure your controller works with the test web. 4.🔺Before desoldering, the main board should be carefully measured with a multi-meter. 5.🔺The soldering iron must be more than 60W. Various soldering materials are needed, however NOT included
[Desoldering Heating Plate] – A copper heating plate melts all the solder joints simultaneously with a soldering iron. Solder Wick and simple PCB holder included. With as many as 14 prongs, removing the problem stick is the most difficult task. It might is not suitable for newbies, though we added these helping hand in the kit
[What’s in box Model: HL-UniA] – 2x Hall Joysticks, 2x Calibration PCB, 1x Heating Plate, 1x Solder Wick, 5x Color Wires for wiring off the PCB, 1x Installation Guide in English alone. (🔺This UniA version of kit was rated 10 difficulty. It’s not for beginners. Teardown screwdriver tools, multi-meter, USB input cables and wired/wireless controllers, other soldering tools and materials are required, however NOT included.)